Kegging and serving your own home brewed beer has never been easier and affordable with the Kegland Oxebar 20ltr Keg and our Universal Regulator.

You could soon be having your own beers on tap at home and serving it to friends and family.

When you start kegging your home brewed beers it will save you all the time that you used to have to spend bottling your beers, this gives you more time for planning your next brew day.

Whats Included:

1 x 20ltr Oxebar Keg

1 x Universal C02 Gas Regulator

1 x Bronco Picnic Party Tap

1 x Gas Ball lock Disconnect

20ltr Oxebar Keg Includes:
1 x 20L Amber Mono Barrier PET Oxebar Keg
1 x Dual PCO1881 Lid assembly with Oxebar Black Handle
1 x KL09164 Green Pressure Relief Valve for Keg Lids / MK4 Reg – 65psi
1 x KL17060 100cm Silicone Hosing with Stainless Steel float and Hop Filter Cage
1 x KL10788 RED Multi Gas Post Plastic Carbonation Cap
1 x KL10788-Yellow Multi Liquid Post Plastic Carbonation Cap

Optional Adaptors Sold Separately

Type A: For attaching Full Size C02 Bottle – pub sized gas bottle

Type B: For attaching Soda Stream Bottle – this will also require Type C Adaptor to attach to regulator, sold together here

Type C: For attaching 16g C02 Gas bulbs

Read below for full details about the Oxebar keg and why this is the perfect introduction into kegging your home brews.

Full details below about the Universal Regulator.

All you need to decide is what gas format you will be using and add the relevant adaptors for either pub sized co2 gas bottle, Sodastream bottle or Gas bulbs.

Oxebar 20ltr Keg

This great value re-usable plastic keg is the best way to store your home brew, great alternative to traditional 19L corny kegs. The 20 litre size is convenient, light weight and perfect for sharing beverages with friends at home.

Not only will it protect your beer from damaging light (amber tinting) it will also keep your beverages fresher for up to 3 times as long due to the Mono Barrier PET Polymer Matrix.

It also comes with a floating dip tube with cage filter. Is easy to undo and stack on top of each-other upside down with disconnects attached.

The 20L Oxebar Amber PET Kegs come with a Green Pressure Relief valve rated to 65psi.

What is Oxebar Mono

Oxebar Mono is a PET polymer blend that utilises several polymers blended together to significantly improve gas barrier properties. When compared with standard PET plastic Oxebar Mono is able to reduce oxygen ingress and CO2 loss so your precious beverage is preserved and shelf life extended by x3.

We recommend this product for beer stored in keg up to 6 months.

Dimensions:

640mm High
235mm Diameter

NOTE: Please check the dimensions will fit in your kegerator as they are a different size to Corny Kegs.

Other uses:

– Overflow Homebrew Keg
– Cleaning Keg for Commercial Keg Buyers
– In a pinch it could be used as a Pressure Fermenter Tank, although we would highly recommend going for a KB03625 30L FermZilla Pressure Brewing Kit for adequate single batch sizing as well as being able to get your hand inside to clean properly.

20L Brimful, ideally 19.5L fill for Kegging purposes.
If you are going to use it as a fermenter, we would recommend between 15L and 18L.
When fermenting you will need a spunding valve. We would recommend the BlowTie.
KL09706 BlowTie Spunding Valve Kit OR KB03529 Integrated Gauge BlowTie Kit (0-15psi)
Remember, a PRV is a not a spunding valve.

During normal everyday use Do not Exceed 4 Bar / 58psi or 45°C

Periodic Hydrotesting Requirement

All pressure vessels should be hydrotested periodically.  This is a very simple process and it’s nothing to be feared.

We recommend that this container be pressure tested every 2 years up to 6 bar.

The instructions for this are:
1. Remove RED prv and fit GREY prv (you can borrow one of these from a 19L keg).
2. Fill keg to the absolute brim with water.  DO NOT forget this step.
3. Use bike pump, CO2 regulator, air compressor or any other pressure source to pressurize the keg to 6 bar.
4. Hold the keg at 6 bar for 1 minute
5. Release the pressure and immediately remove GREY prv and swap back to RED prv.

Note: This test should be done with the keg and water in the keg at room temperature 15-30C

Universal Co2 regulator

The Universal CO2 regulator is a great brewing gas regulator.

Perfect for use at home on a dispense system, also great for mobile dispense on kegs and growlers.

Comes with complete with John Guest 1/4 FFL to 3/8 adaptor included meaning it will work with 3/8 gas line out of the box.

Or it can be used directly on a keg using a threaded disconnect.

It will regulate pressure up and down, venting pressure from the rear to decrease pressure to selected pressure on the dial.

This CO2 regulator can be configured using adapters enabling it to be used with 16g bulbs, Sodastream cylinders or large pub style CO2 bottles. Choose the correct adapters top right of page.

Please note, when using with either a SodaStream cylinder or 16g bulbs the original adapter will need removing from the Universal Regulator.

NOTE: When first attaching to a a new full Sodastream bottle this will vent, it’s important to screw the bottle in fast and fully. You will hear gas vent then the unit seal as it is done up tight.

For more information about brewing, kegging, packaging beer and serving beer be sure to check out our Help Centre where you can find information covering all subjects for brewers of all levels.

And be sure to check out our YouTube channel where you will find videos about brewing, beers, breweries and products.